Version - 1 [March- 2018]

Paper Id ::
 ..........
Paper Title :: Investigation on Gamma Ray Attenuation Parameters of Insulating Epoxy/Barite and Polyester/Barite Composites
Author Name :: M. A. EL-SARRAF
Page Number :: 01-05
:: 10.9790/1813-0703010105   

In the present work, the author investigated the linear attenuation coefficient, mass attenuation coefficient, effective atomic number and effective electronic number for electrically insulating epoxy/barite EP/Br (ρ=2.85 gm·cm-3) and polyester/barite CUP/Br (ρ=3.25 gm·cm-3) composites of radiation shielding potential. The linear attenuation coefficient μ was measured by using narrow beam transmission geometry experimental setup. The experiment was carried on for gamma ray photon energies (0.662, 1.173 and 1.332 MeV) obtained by Cs-137 and Co-60 radioactive sources with the NaI(Tl) scintillation detector.............

Keywords - Epoxy/barite, Polyester/barite, mass attenuation coefficient, effective atomic number, electronic density.

@article{key:article,
author = {M. A. EL-SARRAF},
title = {Investigation on Gamma Ray Attenuation Parameters of Insulating Epoxy/Barite and Polyester/Barite Composites},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {01-05},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Effects of Return on Asset, Return On Equity, Earning Per Share on Corporate Value
Author Name :: Rosikah || Dwi Kartika Prananingrum || Dzulfikri Azis Muthalib || Muh. Irfandy Azis || Miswar Rohansyah
Page Number :: 06-14
:: 10.9790/1813-0703010614   

The objective of this research is to analysis : 1) Identify and analyze the effect of the Return on Assets to firm value, 2) identify and analyze the influence of Return on Equity to firm value, 3) identify and analyze the influence of Earning Per Share on firm value. 4) Identify and analyze the effect of ROA, ROE, EPS simultaneously on firm value. The population in this study were 114 companies listed on the Indonesia Stock Exchange (BEI) in 2006-2010. While the selection of samples was done by using purposive sampling method with the purpose of obtaining representative samples in accordance with specified criteria, Based on the mentioned criteria then the amount of the final sample had complete data in this study a total of 32 companies...........

Keywords - ROA, ROE, EPS, Firm Value.

@article{key:article,
author = {Rosikah || Dwi Kartika Prananingrum || Dzulfikri Azis Muthalib || Muh. Irfandy Azis || Miswar Rohansyah},
title = {Effects of Return on Asset, Return On Equity, Earning Per Share on Corporate Value},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {06-14},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Quasi Reversible Electrochemical Reaction and Metrological Properties in the Time Domain of Flat Voltammetric Electrodes
Author Name :: Krzysztof Suchocki
Page Number :: 15-28
:: 10.9790/1813-0703011528   

Metrological properties of a flat voltammetric electrode on whose surface a quasi-reversible electrochemical reaction takes place were being analyzed in this paper. The conducted analysis showed that such an electrode functions like a measuring converter type I. Its metrological properties in the time domain are defined by sensitivity and a time constant. Results of the simulations proved that these parameters depend on values of indicated ions, a voltammetric electrode construction and parameters of the polarizing voltage.

Keywords - Voltammetric electrodes, voltammetric measurements, quasi-reversible electrochemical reaction, metrologic properties of voltammetric electrodes.

@article{key:article,
author = {Krzysztof Suchocki},
title = {Quasi Reversible Electrochemical Reaction and Metrological Properties in the Time Domain of Flat Voltammetric Electrodes},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {15-28},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: The Optimization of Soluble Cephalosporin C Acylase Expression
in E. coli
Author Name :: Efrida Martius || Ahmad Wibisana || Yovita Ardiyani
Page Number :: 29-34
:: 10.9790/1813-0703012934   

7-aminocephalosporanic acid (7-ACA) is an important intermediate compound for producing of most cephalosporin derivatives. It could be synthetized by conversion of cephalosporin C (CPC) in single step using cephalosporin acylase. The application enzymatic conversion is hampered by low activity of enzyme using CPC as the main substrate. Modification of AcyII Genes from Pseudomonas SE83 produced a high-activity S12 variant on CPC. Based on S12 variant sequence, a synthetic gene was constructed and subsequently transformed to E. coli. The expression of target proteins were performed using LB medium supplemented with ampicillin. Preliminary experiments showed that the target protein (CPC acylase) partially remained as the inclusion bodies.........

Keywords - 7-aminocephalosporanic acid, cephalosporin acylase, cephalosporin, expression, optimization

@article{key:article,
author = {Efrida Martius || Ahmad Wibisana || Yovita Ardiyani},
title = {The Optimization of Soluble Cephalosporin C Acylase Expression in E. coli},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {29-34},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Commercial Motorcycle Safety in Nigeria: The Past and Opportunity for Future Improvement
Author Name :: Oluwasegun O Aluko
Page Number :: 35-41
:: 10.9790/1813-0703013541   

This paper introduces commercial motorcycle as a popular and useful para-transit mode in Nigeria. After reviewing the historic background of this transport mode, it points out its safety problem, nothing that it has been difficult to address this problem. It goes further to review several studies on commercial motorcycle but notes that their findings and recommendations have not improved safety performance in commercial motorcycle operation. Presenting the concepts of driver behavior, and organizational culture and climate it suggests the use of the principles identified in these concepts to address commercial motorcycle safety problem. These principles include developing solutions that take cognizance of the influences on driver behaviour as well as developing policies that can tackle commercial motorcycle operating culture so as to improve its safety climate.

Keywords - Commercial motorcycle, driver behaviour, para-transit, safety.

@article{key:article,
author = {Oluwasegun O Aluko},
title = {Commercial Motorcycle Safety in Nigeria: The Past and Opportunity for Future Improvement},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {35-41},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Evaluation of Physical and Mechanical Properties of Partially Replaced Bamboo Ash Cement Mortar
Author Name :: Mujedu K. A. || Lamidi I. O. || Olomo R. O. || Alao M. O
Page Number :: 42-48
:: 10.9790/1813-0703014248   

The study investigates the evaluation of physical and mechanical properties of partially replaced bamboo ash cement mortar. Various tests such as fineness, soundness, drying shrinkage, air entrainment, water absorption, consistency, setting time, and chemical composition were carried out. The compressive strength as well as density of varying percentage of bamboo ash cement mortar cube of mixing ratio 1 : 6 and water cement ratio of 0.62 were examined and compared. A total of ninety (90) cement mortar cubes of size 50mm x 50mm x 50mm with different percentages by weight of bamboo ash to Portland cement in the order of 0%, 5%, 10%, 15%, 20% and 25% were cast............

Keywords - Bamboo ash, cement, chemical composition, compressive strength, mortar.

@article{key:article,
author = {Mujedu K. A. || Lamidi I. O. || Olomo R. O. || Alao M. O},
title = {Evaluation of Physical and Mechanical Properties of Partially Replaced Bamboo Ash Cement Mortar},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {42-48},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Radiation Model of a Technological Pipe of Nuclear Power Plant
Author Name :: Ephraim Bonah Agyekum || Yu Daneykin || Odii Christopher Joseph || Afornu Bright Kwame || Ansah Michael Nii Sanka
Page Number :: 49-52
:: 10.9790/1813-0703014952   

In this paper, a description of the model of the radiation state of anuclear facility is developed and the composition of the model is outlined.The problems of the formation of the engineering-radiation model of the nuclear facility are considered on the basis of the engineering model of radiation inspectionand gamma radiation calculations depending on the radionuclide composition, the activity of radiation sources, and also their geometric sizes and shapes.Knowing the flux density of gamma quanta of all energies at a given point, one can obtain the absorbed dose rate in the detector and calculate the equivalent dose rate at that point.

Keywords - Radiation,technological pipe, radionuclides, decommissioning, environment, nuclear, power, plant, facility, model, transformation, cylindrical, attenuation, gamma, dose, geometry, coordinates, isotropic, monoenergetic, engineering, flux.

@article{key:article,
author = {Ephraim Bonah Agyekum || Yu Daneykin || Odii Christopher Joseph || Afornu Bright Kwame || Ansah Michael Nii Sanka},
title = {Radiation Model of a Technological Pipe of Nuclear Power Plant},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {49-52},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Fall of Parity in Weak Interactions in the Light of New Physical Theories
Author Name :: L. Venger
Page Number :: 53-60
:: 10.9790/1813-0703015360   

The laws of conservation are the most essential laws of physics. They are universal, strong and unshakable in space and time and are fulfilled always and everywhere. However in 1956 happened a wreck one of these laws. It was the law of conservation of parity for weak interactions. At first American scientists Lee Czun-dao and Yang Chzhen-nin proved theoretically that this law for weak interactions was not fulfilled. Then professor Wu Czyan-syun whith collaborators in Columbian University got the first experimental evidence of fall parity for weak interactions in β-disintegration of radioactive Cobalt-60. Physics outlived shock caused by the wreck one law of conservation...........

Keywords - Conservation, law, parity, spin, torsion.

@article{key:article,
author = {L. Venger},
title = {Fall of Parity in Weak Interactions in the Light of New Physical Theories},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {53-60},
month = {March}
}

Version - 2 [March- 2018]

Paper Id ::
 ..........
Paper Title :: The Effects of Technology in the Modern Office Work Environment
Author Name :: Huthamah Y A A Alruwayyeh
Page Number :: 01-07
:: 10.9790/1813-0703020107   

This research work determined the effects of technology in a modern office work environment. It specifically explored the impact of using latest trends in technology in the managerial, secretarial and other clerical work in modern offices. For a better understanding of the effects, the researcher established first the link between technology and office work. It was found that with the advent of technological advancement, office works required the use of updated technologies for the ultimate goal of being globally competitive. The reasons for adopting technology in offices include reduction of costs of production and services, improvement of performance, increased work productivity, being up-to-date, and becoming at the competitive edge over other markets...........

Keywords - Technology, modern office work environment, displacement The Effects of Technology in the Modern Office Work Environment

@article{key:article,
author = {Huthamah Y A A Alruwayyeh},
title = {The Effects of Technology in the Modern Office Work Environment},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {01-07},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Indoor To Indoor And Indoor To Outdoor Millimeter Wave Propagation Channel Simulations At 26 Ghz, 28 Ghz And 60 Ghz For 5G Mobile Networks
Author Name :: W. Manan || H. Obeidat || A. Al-Abdullah || R. Abd-Alhameed || F. Hu
Page Number :: 08-18
:: 10.9790/1813-0703020818   

In this paper the characteristics of LOS and NLOS propagations channels are intensively investigated under three mm wave frequencies; 26GHz, 28GHz and 60GHz for vertical polarized omnidirectional antenna. The simulation data achieved from the 3D shooting and bouncing Ray (SBR) tracer based on the effects of frequency dependent electrical properties of building materials and has been observed that signal is much affected by the nature of building materials and frequencies for line of sight and non-line of sight.

Keywords - 5G, Line of Sight (LOS), Non-LOS (NLOS), Delay spread, path loss.

@article{key:article,
author = {W. Manan || H. Obeidat || A. Al-Abdullah || R. Abd-Alhameed || F. Hu},
title = {Indoor To Indoor And Indoor To Outdoor Millimeter Wave Propagation Channel Simulations At 26 Ghz, 28 Ghz And 60 Ghz For 5G Mobile Networks},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {08-18},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Design and Simulation of Solar Animated Simulator for Functional Testing Of Spatial Systems and Design Analysis in Zemax Software
Author Name :: Farhad Fani Saberi || Marziyeh Razavi Nejad || Hashem Bazrafshan || Mehdi Zandieh
Page Number :: 19-29
:: 10.9790/1813-0703021929   

In order to test the performance of solar sensors that are installed with a particular layout on the satellite body, laboratory testing is required. Therefore, facilities and hospitalization should be provided so that in the presence of physical agents, such as sunlight, they can actually see the results. The solar simulator is a device used in space laboratories to test solar sensors. In this paper, the optical system and light source of the solar mobile simulator are designed according to the requirements of the test conditions. This optical system consists of a halogen light source, a parallel lens, a flat mirror and a meter that has a surface level of three degrees of freedom of the satellite's location in the test bed. The results of the optical system analysis in the Zemaxsoftware show the proper performance of the system, including the intensity of light, the diameter of the stain and the uniformity of the received light at the level of the data.

Keywords - Sun light simulator- The satellite- Optical light source- Parallel lens- Detector- Zemax software.

@article{key:article,
author = {Farhad Fani Saberi || Marziyeh Razavi Nejad || Hashem Bazrafshan || Mehdi Zandieh},
title = {Design and Simulation of Solar Animated Simulator for Functional Testing Of Spatial Systems and Design Analysis in Zemax Software},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {19-29},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Optimization of a Permanent Magnet Synchronous Motor
Author Name :: Szilard Jagasics || Prof. Dr. Istvan Vajda
Page Number :: 30-35
:: 10.9790/1813-0703023035   

Permanent magnet synchronous motors are widely used due to their high power to volume ratio and performance. Every application has its own requirements for the motor. Therefore, their design optimization process is getting more complex. It is recommended to think over the parameters at the beginning of optimization. Too much parameters may result in a too complex solution but if one of the important ones is left out the process is incomplete. The main task of an optimization is to find the parameters which mainly influence the properties of the product.

Keywords - Cogging torque, optimization, sizing, pmsm.

@article{key:article,
author = {Szilard Jagasics || Prof. Dr. Istvan Vajda},
title = {Optimization of a Permanent Magnet Synchronous Motor},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {30-35},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Optimization of Production Cost and Distribution Network of Nigerian Bottling Company Plc
Author Name :: Engr. Dr. A.C. Uzorh || Engr. I. Nnanna
Page Number :: 36-54
:: 10.9790/1813-0703023654   

This research on optimization of production cost and distribution network was carried out in the Nigerian Bottling Company (NBC) which has many production facilities and multi -products systems. Three plants and twenty two warehouses within the South-South and South-East region of Nigeria were selected for this study. Production operations of the three plants were monitored and data obtained were analyzed using operations research technique. A mathematical model that captured supply chain network problems of the company was developed using mixed-integer programming approach. The model consists of one hundred and ninety six (196) variables and one hundred and twenty six (126) constraints. A programming software known as Lingo Model (15.0 Version) was used.........

Keywords - Supply chain, Optimization, model, Production, Inventory, Distribution, mixed - integral.

@article{key:article,
author = {Engr. Dr. A.C. Uzorh || Engr. I. Nnanna},
title = {Optimization of Production Cost and Distribution Network of Nigerian Bottling Company Plc},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {36-54},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: On The Propagation of Free Waves in Viscoelastic Layered Bodies
Author Name :: Ro'ziyev Т.R. || Nuriddinov B.Z. || Khojiyev А.
Page Number :: 55-63
:: 10.9790/1813-0703025563   

At this work the propagation of natural waves in dissipative inhomogeneous planar bodies is discussed. Wave motions are described by linear integral-differential equations. Solving this problem, we obtain a relationship between the wave velocity and its length. The task of this kind is of great interest for geophysicists, in the field of engineering and construction.

Keywords - Viscoelastic half-space, layer, equation of motion, phase velocity.

@article{key:article,
author = {Ro'ziyev Т.R. || Nuriddinov B.Z. || Khojiyev А.},
title = {On The Propagation of Free Waves in Viscoelastic Layered Bodies},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {55-63},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Evaluation of the Performance of Brick Dust as a Filler Material for Hot Asphalt Mix Design: A Case Study in Jimma Zone
Author Name :: Fisseha Wagaw || Prof. Emer Tucay Quezon || Anteneh Geremew
Page Number :: 64-72
:: 10.9790/1813-0703026472   

A bituminous paving mixture is a mixture of coarse aggregate, fine aggregate, and bitumen mixed in suitable proportion to result in the strong and durable mix in order to withstand traffic load. In this paving mix, ordinary stone dust, and cement used as filler material. One of the main problems in the construction of bituminous paving mixture is the insufficient amount of filler from crushing stone aggregate, and cement supply is low. A study has been carried out in this research to explore the use of Brick dust as filler material for the bituminous mixture. The objective is intended to evaluate the performance of brick dust as fillers in Hot Asphalt Mix design, according to the test procedure specified by ASTM..........

Keywords - Aggregates, Brick Filler, Bituminous paving mix, Hot Mix Asphalt, Marshall Mix Design, Optimum Asphalt Content.

@article{key:article,
author = {Fisseha Wagaw || Prof. Emer Tucay Quezon || Anteneh Geremew},
title = {Evaluation of the Performance of Brick Dust as a Filler Material for Hot Asphalt Mix Design: A Case Study in Jimma Zone},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {64-72},
month = {March}
}
Paper Id ::
 ..........
Paper Title :: Effect of Geometry in Wire Grid Polarizers on Contrast Ratio of Display Panels
Author Name :: Moon Young Shin || Hyunsik Yoon
Page Number :: 73-76
:: 10.9790/1813-0703027376   

In liquid crystal display (LCD) panels, there are two polarizing films and liquid crystal tunes the polarization of backlight. As large the size of the panel is, the polarizing film becomes expensive because of the fabrication cost of the film. Wire grid polarizers (WGPs), which consist of metal wires on a transparent substrate, could be the alternative for the large area LCD panels. In this study, we investigate the effect of the geometry of the wire grid polarizer on the contrast ratio, which is an important property in LCD device. We conduct a simulation with WGPs in different tip shapes and different design of protection dielectric layers and extract the data for obtaining contrast ratios. The contrast ratio of the WGPs with sloped edges is lower than that of WGPs with straight edges. In addition, dielectric layers should not fill the gap between the metal lines to ensure high contrast ratio.

Keywords - wire grid polarizers, liquid crystal display, tip shape, dielectric layer, metal wire.

@article{key:article,
author = {Moon Young Shin || Hyunsik Yoon},
title = {Effect of Geometry in Wire Grid Polarizers on Contrast Ratio of Display Panels},
journal = {The International Journal of Engineering and Science},
year = {2018},
volume = {07},
number = {03},
pages = {73-76},
month = {March}
}